Jump to content

My Slice of Nature (Part 3)


SubzeroLT

Recommended Posts

  • SRC Supporter

Starting a new thread to document the progress of a new set up.

Tank was given by a nice reefer (thanks!!). In return, I bought over his equipment.

 

Its a nice sized tank - 5 x 2.5 x 2, 15mm glass, chengal wood stand. The physical condition of the tank wasn't great and took it as part of the fun to fix it during free time on the weekends. Some pictures :

P7160884 (Large).jpg

 

Upon closer inspection, there are several large patches of scratches in the middle (viewing area)

P8060191 (Large).jpg

 

Ordered some Cerium Oxide - a compound commonly used in the industry to polish glass

P8060909 (Large).jpg

 

Mix into a paste

P8060910 (Large).jpg

 

Marked the areas with bad scratches with masking tape

IMG_9968 (Large).jpg

 

Climbed into the tank & polished out the scratches. I'd say 90% of the bad scratches are gone. I didn't bother to remove the scratches from areas which were not easily seen.

IMG_9970 (Large).jpg

 

 

  • Like 2

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • SRC Supporter

Did the usual process of cleaning the rocks

Bleach, soak, scrub the rocks for a day or so :

P7060876 (Large).jpg

 

Then rinse with tap water / anti chlorine a couple of time. Having a large open bucket like this 120L one from ikea is great

P7170890 (Large).jpg

 

Having some water movement should improve the efficiency to remove the bleach. Soaked the rocks in tap water for a few days.

IMG_9709 (Large).jpg

 

Let the rocks dry, then vinegar soak for 15min. 

P7270907 (Large).jpg

 

 

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • SRC Supporter

Original plumbing was the 'traditional' overflow with one drain & 1 return. These type of plumbing is known to be noisy. Hence it was converted into a Herbie overflow instead.

IMG_9688 (Large).jpg

 

Noticed that the original fittings used had a potential issue.

IMG_9924 (Large).jpg

Only 1-2 threads were engaged when this was fit through the bottom of the tank. High risk of loosening -> risks of leaks.

 

This was a 3/4" pipe and I could not find fittings with longer threads. Got a external threaded pipe & made a bulkhead with longer threads.

P8130940 (Large).jpg

 

Cut out a gasket from a sheet of EPDM rubber. To be used between the bulkhead & glass (instead of using silicon sealant)

P8130936 (Large).jpg

 

Drainage piping done

P8140945 (Large).jpg

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

Nice setup!! Camping here.

  • Like 1

Display Tank : 36" x 20" x 20" Herbie overflow box design, Sump : 36" x 21" x 17", Frag Tank : 16” x 20” x 16”, custom built by Tank Culture.

Lightings : Ecotech  Radion XR15 Pro x 2 for Main Display Tank, Inled R80 x 1 for Frag Tank.

Chiller : Dalkin 1hp compressor with build-in drop coil.

Skimmer : Skimz Octa SC205i Protein Skimmer.

FR : H2Ocean FMR75 Fluidised Media Reactor with Hailea HX-2500 (Feeder Pump) running Rowaphos.

CR : Skimz Monzter E Series CM122 Calcium Reactor.

BPR: Marine Source Biopellet  Reactor with Continuum Reef Biopellet Fuel. 

Main Return Pump : SICCE Syncra ADV 9.0 & Jebao ACQ-10000 Water Pump.

Wavemaker : Jebao MOW-9 x2 for Main Display Tank & Jebao SLW-20M  Sine Wave Pump for  Frag Tank.

Water Top Up: AutoAqua Smart ATO Lite.

Link to comment
Share on other sites

  • SRC Supporter

Someone commented separately that the tank looked so new. In actual fact, this was what it was like initially when tank was moved on 7th July

 

3B1EB29F-213E-4734-A380-93DC6CFA954D (Large).jpg

 

71A94E78-BA47-4117-A9E7-6F226F7987D6 (Large).jpg

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • SRC Supporter

The gate valve is quite heavy & not located directly underneath the bulkhead. I was worried it'll compress the gasket unevenly over time. Hence the pipes were secured with a scrap piece of aluminum profile

P9041447 (Large).jpg

 

 

 

 

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • SRC Supporter

Omg. Can Really can see alot of effort and hard work go into the restoration of the tank and setup.

Thanks for sharing, alot of reefer will benefit from your share here as always.

Sent from Singapore Reef Club mobile app

Link to comment
Share on other sites

  • SRC Supporter
23 hours ago, Sherilyn91 said:

Swee.. Looking forward to see the end product..


Sent from my iPhone using Tapatalk

Tank progress quite slow. I will make it to your place one of these days. 

 

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • SRC Supporter
15 hours ago, dsam said:

Dun mind the questions,

Can share the specs of the gate valve, slip on x NPT thread?

From Hai Cheong?

Is the dark grey pipe sch 80 type?

That's a Spears gate valve. 1" slip fitment. Yes, I got Hai Cheong to order for me but they applied a very high mark up :(

Nevermind...just 1 piece.

 

The dark gray pipe is some leftover schedule 80 1.5" pipe i had left from my previous tank project. Hence, everything upstream is upsized to minimize losses.

Schedule 80 is absolutely unnecessary for our tanks. It was a newbie error made the last time.

 

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • SRC Supporter
On 9/6/2016 at 8:10 AM, Jason Ng said:

Yes. Great info. Thanks for sharing. Can tell where u get the piping stuff. Thanks

Sent from my SM-G900F using Tapatalk
 

Most of my piping stuff are from Hai Cheong Plastic (Located at 11 Kallang Place).

B6DD6A65-03A9-4C77-B010-BD96BB472FB3 (Large).jpg

CD703820-05E6-42D7-AA52-14492B067B24 (Large).jpg

 

Alternatively, you can get a good selection at Madpetz or good neighbourhood hardware shops.

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • SRC Member

Thanks for the reply. Wonder if you compare the cost with BRS? Yea, Sch 80 is always a pain to construct with compatibility issue. But their Sch 80 bulkhead is very solid.

Watching your Part 3 closely. Your tank thread always gives lots of inspiration and ideas to us. Great job!

Link to comment
Share on other sites

  • SRC Member
On 9/4/2016 at 11:47 PM, SubzeroLT said:

Original plumbing was the 'traditional' overflow with one drain & 1 return. These type of plumbing is known to be noisy. Hence it was converted into a Herbie overflow instead.

IMG_9688 (Large).jpg

 

Noticed that the original fittings used had a potential issue.

 

Only 1-2 threads were engaged when this was fit through the bottom of the tank. High risk of loosening -> risks of leaks.

IMG_9924 (Large).jpg

This was a 3/4" pipe and I could not find fittings with longer threads. Got a external threaded pipe & made a bulkhead with longer threads.

P8130940 (Large).jpg

 

Cut out a gasket from a sheet of EPDM rubber. To be used between the bulkhead & glass (instead of using silicon sealant)

P8130936 (Large).jpg

 

Drainage piping done

P8140945 (Large).jpg

Hi bro.

I have the longer version which is 1" type.

You can get it from malaysia or a HW shop at AMK industrial park.

Tank : 3 x 2 x 1.8 ( setup end Feb 2014 ) --> 4 x 2 x 1.8 ( setup early Nov 2016 )
Skimmer : Bubble Magus NAC6 --> Bubble Magus Curve 7
Return pump : Jebao 10000l/h ( down in 17th December 2014 ) --> Jebao DC-12000 ( 19th December 2014 )
Compressor drop-in coil
Wavemaker : Tunze 6105 x 1
Lights : Modular based DIY LED light x 4

Chaeto in the sump

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.




  • Join us on the largest Reefing community in Asia!

    Sign up and share your reefing journey with us, make friends and get helps from the community .

     

  • Topics

  • Latest Update

    1. 0

      ¡Cuevana! ver Garfield: La película (2024)—Gratis en Español y Latino utm

    2. 0

      [!PELISPLUS¡] Ver Cinderella's Curse (2024) Online en Español y Latin hlx

    3. 0

      [.WATCH.] Daaaaaalí! (2024) (FullMovie) Free Online on English dtx

    4. 0

      Maymunlar Cehennemi: Yeni Krallık (2024) Filmini Ücretsiz İzlemek İçin En İyi Çevrimiçi Akış Seçenekleriyle İzle wbk

    5. 0

      [!PelisPlus] Hit Man (2024) Película Completa - ESPAÑOL LATINO lam

×
×
  • Create New...