DottyClown

All reserved.

GSP A : $10 (2cm plug) GSP B : $20 (3cm plug) Xenia : $20 each frag GSP B overgrow from plug to frag tray. Will detach as much area as possible from tray so that Buyer should get more then the plug size. Xenia are freshly glued to plug today, after they had attached themselves to the coral chips. Collection at S(100059), preferably this Saturday 6-9pm. Free delivery to West area for Saturday after 10pm.

Only left GSP A&C. Going west side this afternoon, maybe around 4pm. Can do free delivery on my way, if anyone interested.

Both frags of Xenia and GSP (B) reserved. Left GSP (A) and (C). Will still be fragging my Xenia colony as it’s getting big. So will have more to come.

Have 2 frags of Xenia, $20 each. Serious pulsing. And GSP (A)$10, (B)$15, (C)$20. Frag C overgrown onto tray, so will try best to pull off with the plug. Collection (100059). Deal lift lobby. FullSizeRender.mov

Reserved by xxxxx190.

Ups. Would rather sell whole than to break into smaller frags.

Multiple stalks of Xenia on a 12cm Tonga rock. $50, the piece on sand bed in video. IMG_7220.MOV

What volume and length is your tank?

Hi, interested in the Hammer. Where’s location? Possible to see side view/stem/mouth of the 2 hammer frags?

Frag tray overgrown with GSP as had no time to trim. Looking to sell off the “culprits” that created this beautiful meadow of GSP. 2 x Frag plugs @ $15 each 1 x small rock @ $25 Small rock approx 6x4cm, I think. Take reference is to the Sunny-D zoas for plug size. (1 plug removed in photo, the other still on tray.) Location S(100059) PM if interested. IMG_4622.MOV

Both buckets taken. Thread closed.

Ups

Have 2 x 20kg buckets of salt-mix to let go. Each for $55. PM to arrange collection or delivery.

Or if anyone want to share, I’ll buy the 2+1 offer of 20kg, keep 1 pail for myself and sell the balance at $55 /pail. Can deliver for $5.

Anyone have extra pail of PUR Reef Salt to let go, please PM me with price and location. Tks.

Wonder if it’s anything to do with me adding some baby toadstools. But these new additions are all very small still, couldn’t have that big an effect leh.

Had this piece for almost 2 years. First time in this “drooping” condition and it’s over a week. Normally how long could it be in this condition?

It’s been a week since my toadstool did not open/extend it polyps. Today’s it’s slouching down and the edges browning. Is it a gone case?

For all that have had unpleasant encounter with this Reefer, please report you case to SRC and let them decide if any actions they need to take.

Please report your case to SRC as per above post from SRC moderator.

So Senses, Jazzi and jd_n all have bad experience with this jj guy? Then there could be more silent victims.

Was using the Tunze 9001 in my previous 16G tank. Now am running a 30G tank with this 9001. Considering to change to the Tunze 9004. Would appreciate any other suggestions for Skimmer better/equal to the 9004. My 30G is an IOS tank, so compartment to mount Skimmer is only about 13cmx13cm. TIA

Bro, what’s behind the Chiller? The air out/exhaust to where?

Not impossible but very tricky. For example, you have a few big considerations to consider. 1) The bioload will increase, so can your existing system handle it sufficiently or is there another system in 2nd tank, and only sharing chilled water. 2) Need to plan very carefully on both pumps used to prevent overflow on a tank when the other pump fails, or if pumps are not matched perfectly. 3) The distance between tanks could cause an increase in chilled water Temperature, thus your compressor may kick in longer and more frequently than usual. Worst case, is perpetually running if temperature increase during piping is too much.