Jump to content

My Slice of Nature (Part 3)


SubzeroLT

Recommended Posts

  • SRC Supporter
4 hours ago, ben loh said:

So u replace the Alkatronic, mastertronic to trident? 
wat r the factor tat leads u to trident?

I'm still running the Alkatronic & plan to continue using it. Still find it very practical & economical to run, especially as a calcium reactor user. Its been running reliably since Feb 2018 with just one tube change so far. Mechanism is proven to be reliable and software is pretty good nowadays.

 

The mastertronic is covenient and replaces manual measurent using standard test kits. In particular, I find the Phosphate measurement capability good (170 tests with Red Sea test kit). One challenge with the Mastronic the past year is the avaliability of some reagents locally (eg. Phosphate & Magnesium)

image.png.ad842e44e2d6ad286eff523443afe396.png

I don't have a Dosetronic which executes a balanced dosing based on Alkalinity readings from the Alkatronic (not mastertronic)

 

Personally I'm testing the Trident to have more integration with the Apex ecosystem. What I have in mind is to integrate with the DOS pumps for dosing. And be able to set a target value & automatically dose. I may be travelling for work in the coming months & want to have a backup dosing system in case the calcium reactor has problems (bad experience in the past of effluent clogging or run out of CO2 when I'm out of the country). 

 

While there are a few other automated tester brands to consider nowadays, another factor I considered is having prompt & strong local technical support from Reef Depot during or even beyond warranty period. 

 

 

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • SRC Member

Agree on the availability of regents..  but why you dun use alkalinity function on trident to use on CR instead of having 2 machine. Coz I’m thinking if can use 1 machine on CR and also measure CA n MG. 

Link to comment
Share on other sites

  • 2 weeks later...
  • SRC Supporter
On 6/30/2022 at 8:09 AM, ben loh said:

Agree on the availability of regents..  but why you dun use alkalinity function on trident to use on CR instead of having 2 machine. Coz I’m thinking if can use 1 machine on CR and also measure CA n MG. 

I think both ways work.

In any case, I think the Alkatronic is very practical for Calcium Reactor since alkalinity is a good reference for the effluent and also a good closed loop check if something goes wrong with the CR system.

 

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • SRC Supporter

Noticed the downflow slowing down. And more water flowing into the emergency drain. Probably time to clean the clarisea pipe.

image.jpeg.64a754528656509500fd9ab4a8bc3f34.jpeg

 

As expected the internal pipe is filled with debris. This extra work could have been avoided by having a finer grill over the down pipe in the overflow area.

image.jpeg.d551ce26a121665c004042a9211a73e3.jpeg

 

Trimmed one of the pink birdsnest colony and had to use rubber band to stabilize it while the glue dried.

464580969_IMG_7631(Large).jpeg.97b4caf7292431e923652de981713d02.jpeg

 

View of the other half of the tank. 

image.jpeg.da5889e6566898a6116b3e8474be0a63.jpeg

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • 3 weeks later...
  • SRC Supporter

CO2 tank empty.

20th Feb -> 25th July => 5 months 5 days. Not bad.

image.jpeg.46cfdd786914e468aac11e9deb4017cb.jpeg

 

Actually the CO2 pressure started to reduce probably on 24th July but I didn't set the warning PH thresholds correct in the Apex programming. Probably a typo error during the old/new Apex transfer. I received the email warning at 7.6pH instead of 6.7pH.

image.png.b1ea6feaa8daba67a79612051f7723ab.png

 

Because of this, KH dropped drastically on 25th July from ~ 8.3KH to 7KH in a day.

image.png.f74f444ca307ec7ff7a30586c829a5d8.png

 

By the way, the CO2 Art regulator is very reliable so far. The O-ring is a hard plastic which does not squish or detiorirate so easily.

image.jpeg.d2f42f0b70f94904ba41ce4e3e508a8d.jpeg

 

CO2 regulartor programming :

image.png.e5ea490a9a15fbc2320641a1638d2916.png

 

This virtual outlet is to fine tune the timing to switch off the CO2 in order to maintain the  KH levels within a day.

image.png.66f49fc81039e22f75054d117d7b03ca.png

 

Virtual outlet to toggle notification when running out of CO2

image.png.d7ae049de4c5f7439b040e165907c696.png

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • SRC Supporter

Trident's alkalinity reagent finished last week and i finally managed to find time to swap it out this weekend. Process is quite simple.

Just click on the task icon to triger the manual & process flow.

image.jpeg.b85d38431ff8435b0af6aadb08f3c9b5.jpeg

 

image.png.fe5070a44b9e46098cf923cbfdc51c93.png

 

Step by step with instructions

image.png.c9b5849c7f84f783d1c3e2664b20f049.png image.png.14ecb567c69620db14c3887645413190.png

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • SRC Supporter

Very often, we wish to know the flow rate of our return pumps or more importantly, through the UV sterilizer.  Recently I got an Apex flow sensor (1" size). Here are some thoughts that went into the piping retrofit. My AquaUV is located outside my sump but the space is quite tight.

image.jpeg.85e884e1dc0bd166330b06c548e03a4c.jpeg

A proper method of using the flow sensor is to set it up to measure flow only when needed. These flow sensors should not be run 24/7 and in-line with the main flow. Aside from excessive wear & tear, it'll be subject to clogs (eg chaeto or vermatid snail bits getting stuck on the paddle wheel). While its nice to know the flow rate at any point in time, or to be triggered when flow slows down, the trade off far outweights the benefits.

The initial plan was to set it up this way. This would be the way i'd have set it up during initial tank setup. Have a splitter and valves to direct the flow to the flow meter as necessary.

image.png.fd19f69fcf607a97bb1bfceb7690212e.png

 

Bought the piping required.... but the assembly is too large.

image.jpeg.f70e6ad6e2a530c4865a99cb653b3fbe.jpeg

 

But finally decided to go with something simpler & more versatile -just plug directly into the hose to measure as and when needed. With the threaded fittings, I could change to different fittings for different setups.

image.jpeg.9981f76942ba2f6e86fdaacc1741317d.jpeg

 

Setting it up to Apex Fusion is simple.

 

Plug the flow sesnor the the FMM module.

image.jpeg.7a6708015d705639752e8fd55a88dd2c.jpeg

 

From the task selection, select "Flow Sensor"

IMG_8524.PNG.3824eb6aa71ab957d53634cbf3ad016d.PNG

 

Select the FMM module

IMG_8525.PNG.792137dae1e3f54661f95c3a1bedefab.PNG

 

Select the port then rename it accordingly.

IMG_8526.PNG.dbeb49c58d3c325376da314959ad10bd.PNG

 

Select the size of the flow sensor.

IMG_8527.PNG.8a54a49ff91248b7adfcb355a4a48a42.PNG

 

Once done. new tiles will appear. Then drag onto the dashboard.

image.png.a4a60880b7b8a6e2e31981c6f81c304b.png

 

That is is the flow rate through my UV sterilizer. 117 G/hr = 442 L/hr. WHAT!! So low flow rate!!  Absolutely not maximizing the UV effectiveness at all. 

From here, I did some changes to the tubing and pump power to significantly improve the flow (will share more on this in the next post).  Its so good to have a flow sensor handy to optimize the system and to know its possible to get up to 1817L/hr through the UV with my current plumbing & pump.

 

Checking flow through the UV sterilizer

image.jpeg.5ce41f1c9416432d772254835a47d7b5.jpeg

 

image.jpeg.1f8a8c341b3a57dc38fb9eb014caad75.jpeg

 

 

 

 

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • SRC Supporter

UV maintenance weekend and to improve flow.

 

AquaUV's recommendation is to change the bulb every 14 months of continuous use. My last change was October 2020 - so that's about 1yr 9 months / 21 months.

 

754304520_P1010079(Large).JPG.9f09eda73ff227c8ecf304d9a13e6f71.JPG

The quartz sleeve is genarally OK. Some dried salt at the oustside top (because my unit is orientated vertically). A brownish tint on the outside.The inside of the sleeve is a little hazy. 

901337353_P1010075(Large)(1).JPG.a1b889bcdbf845e8d1cebaebc61b26b7.JPG

 

 

IMG_8536.JPEG.805027b7efff4889277a29170c87fc50.JPEG

 

Washed both sides with some citric acid cleaner from AE.

763424771_P1010076(Large).JPG.d508eca409929cd0aa0883882535351f.JPG

 

In the earlier post, i mentioned about the slow flow rate of 117 G/hr (442L/hr).  So I made some changes to eleminate some bottlenecks.

IMG_8531.PNG.7c53474fb2f281a66fa97401e2acfa25.PNG

 

The 1st thing is the barb fittings that came with AquaUV.

Its a integrated 19m & 16mm barb. By right, one should cut off the 16mm section if using a 19mm hose else its really just running as 16mm diameter equivalent. In any case, i was using a 16/22mm hose. That's typically the largest available at Clementi fish shop (C328)

IMG_8614.jpeg.6c19c9ffb1838d1560db1042825a2b6d.jpeg

 

In any case, i changed mine to a Spears 3/4" to 20mm fitting (gray). IMG_8541.JPEG.ead135a285b46aed8f54f6d1a0b8aa6a.JPEG

 

Also got rid of all the 16/22 hose and eheim joints. These are all serious flow restrictors. 

IMG_8555.JPEG.b69d08c6ea417741401bea1edb5ae0f0.JPEG

 

I found 19/25 mm silicone hoses at ReefmarketSG.

These are 3mm thick - won't kink easily. And they won't harden over time unlike PVC tubing. Good quality stuff.

IMG_8551.JPEG.cbb500ea9d861681d9d09e66954b6bc2.JPEG

 

Original setting. 16mm tubing + Eheim quick fitting= 117 G/hr = 442 L/hr @ 25% power 

Tune up power  to get 156 G/hr = 601 L/hr @ 35% power

 

Change to 20mm fitting & 19mm hose

  • 351 G/hr = 1328 L/hr @ 35% power
  • 372 G/hr = 1408 L/hr @ 45% power
  • 406 G/hr = 1536 L/hr @ 60% power
  • 461 G/hr =  1745 L/hr @ 90% power
  • 480 G/hr = 1817 L/hr @ 100% power

Putting this into a chart

409361947_S1AquaUV.JPG.35599355e2a959a3b5cd19ff60c8bce8.JPG

 

Screen shot of the dashboard. Hmmm... need to figure out how to set the display to L/hr intead of G/hr

IMG_8564.PNG.38ac50e7d7cfb570dbcfe8a680aed5d0.PNGIMG_8566.PNG.cc9125155ce418a6db677f7bf7b86014.PNG

 

 

IMG_8549.PNG.852c25c7b6c192a10bb91a415611a5f4.PNGIMG_8556.PNG.973751d964af4d55012a1c72cc8bdc61.PNG

 

 

 

 

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • SRC Supporter

Replaced my old button assembly for the Apex made about 7 years ago. In the old days, a small project box was used with holes cut out (Below pic from July 2015)

 image.jpeg.53db3a0929732e7199a6609fd595c919.jpeg

 

Fast forward to 2022, the case can be 3D printed now. One of the issues I had the past years was switching off the skimmer to drain/clean it but forget to switch it back on. Only to realise it a few days later.

This time, i got a trigger switch with a cover that you can visually see if ithe switch is off. I tried powering the LED on the switch but somehow it does not work properly when connected to the breakout box (lit up in both ON/OFF position).

image.jpeg.5f34cf6880bf61b7f744b22d37d3d605.jpeg

 

Internal view. The wires then connect to the breakout box.

786714533_P1010070(Large).JPG.591bc60aadd7f64647d9d86385394ef9.JPG

 

Installed near the door. Hmm....looks a bit bright. Perhaps it should have been printed in black.

845298057_P1010176(Large).JPG.5c4cfd6df1d66872b1c566814e32efc4.JPG

 

Switch cover is lifted whent the skimmer switch is in the off position. Using this as a visual que.

image.jpeg.2802f19fc15b35f3bb543fe9f3e8f5db.jpeg

 

The momentary Green button is pressed when I dose things like bacteria & trace elements. Turns off the skimmer & UV for  2 hours in an effort for the stuff to do its thing when freshly dosed.

Set OFF
If SW_Gre CLOSED Then ON
Defer 120:00 Then OFF

 

The momentary Red button works similary when I feed the tank with phyto & reef roids - switch off the skimmer for 1 hour so it gets recirculated for a short while.

 

The Blue button is not programmed at the moment. Possibly for future purposes when there are more scripting features on the Apex.

 

 

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • SRC Supporter

Making a Kalk Reactor

More broken things that needed to be fixed.

My old Kalk stirrer could not seal properly recently. O ring flattened & expanded. Reactor was given by Larry some time back (thanks!)  Need a replacement O-ring which will take some time to arrive.

176523414_P1010178(Large).JPG.afe1dfb156eca30ad9cb4442ad412487.JPG

 

In the meantime, I decided to repurpose an old calcium reactor secondary chamber and whatever pipe fittings into a kalk stirrer.  The Bubble Magus reactor has an outlet at the outside/bottom of the reactor. I didn't want to use this as the fresh water input. Wanted to seal the bottom inlet off so its more maneuverable.  Plan to use the fitting at the top of the reactor as the water inlet & outlet.

Firstly, mark a hole & cut out with a dremel.

image.jpeg.985b9cecc63ce30660d8e20d580d68f9.jpeg

image.jpeg.e84a90b5574f0a2166bb8ff80c603828.jpeg

 

Then make a gasket for the elbow pipe. Center hole cut out using 50c coin as template.

image.jpeg.34db6676c3c15310a9d4781155b6e9d5.jpeg

 

Water inlet through the center blue fitting. But i wanted the fresh water to be fed to the middle of the reactor (not just at the top). So I 3D printed a tube holder.

image.jpeg.0b0f7b4d756d9e94dc0e5620c5625624.jpeg

 

image.jpeg.7e46ea5b43bdb09eb8a854724ef18eab.jpeg

 

3D printed a rim for the glass.

image.jpeg.c4607ba6725243dfef82ec19ebcc32ec.jpeg

 

The rim is then glued to the base of the reactor.

image.jpeg.457b94bcd0488f65bb0000cddaa93eb4.jpeg

 

The purpose of the glass is to prevent wear on the acrylic base when the stir bar spins.

image.jpeg.be820fdaf6708eaa86e5cfb5f3e6a09f.jpeg

 

All hooked up. Water is fed via the Ecotech Versa. The magnetic stirrer is made from an old CPU fan with magnets attached to the base (refer to earlier post). Stirrer spins every 15 minutes for 15 seconds.

Stirrer starting up :

image.jpeg.16ae2d6c6884f4a72d8d3ca0c5e1e52e.jpeg

 

After 15s

image.jpeg.9bba6dce047cc57fcbe13e78bc6bd883.jpeg

 

Effluent outlet into the sump.

image.jpeg.cdd7862c5280854b1f2cdea530c33c7a.jpeg

 

Versa setting. Total 2.1 L per day.

image.png.29208df74dda1ce9deb82b24a900154d.png

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • SRC Supporter
On 8/12/2022 at 3:31 PM, he said:

Seem like there is so much use for the 3D printer , do u sketch those dimensions of the item yourself to be printed?

Sent from Singapore Reef Club mobile app
 

Yep...self drawn on CAD software. Not difficult.

 

Some recent printouts 

A new version of a tube holder mounted in front of the Vectra M2 return pump. Purpose is place the outlet of the UV sterilizer right in front of the inlet of the return pump - so that all the 'clean' water goes straight to the display tank. By placing it right in front of it, perhaps 95% of the water goes up....and not get recirculate within the return section of the sump.

 

image.jpeg.d4014502188a56eadb7ad50178821c2c.jpeg

 

What it looks like.

image.jpeg.a296ee0b57a67eb09efda7cc1502453d.jpeg

 

 

Also made this clip +pinch valve for the sulfur reactor.

image.jpeg.354049470d907ac9511ad89b22c1ea2e.jpeg

 

Clips onto a holder in the sump so the effluent tube is well within view. And a thumb screw to control the drip rate.

The clips keeps it securely in place. Had a bad experience where the tube slipped out to the outside of the sump when I was out the entire day.

image.jpeg.f537f2b0a49126f1da4d3c693ee80e77.jpeg

 

 

 

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • SRC Supporter

Some recent coral pics

 

From a frag previously from Mike Stone in 2020.

image.jpeg.c6763b3aa5d0f12becd07e378ec75b40.jpeg

 

 

image.jpeg.6fa08e1f3bbbbfa3d88621657c4268a3.jpeg

 

Corner prata collection. All from The Reefer. 

image.jpeg.fdeb9889b1d30904d06a26f6d9217d13.jpeg

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • 3 weeks later...
  • SRC Supporter

Received several queries recently about

  1. Managing water parameters and water quality,
  2. The type of bacteria to dose when cycling a new tank,
  3. Whether there is a need to dose bacteria in an established tank.

Hence I’m sharing my process & views about a group of products I’ve been using.

 

Firstly, water parameters & water quality are linked but not exactly the same thing. Water parameters are quantitative & easier to track. (1) Measure the major water parameters weekly at minimum (eg. Ca, Mg, KH, NO3, PO4, K) and adjust your process/dosing accordingly. And (2) Dose your trace elements & check with ICP as often as you can afford. 

Water quality is more qualitative. Its equally important but often overlooked. A big part is linked to biological filtration – the conversion of toxic ammonia to harmless nitrates, the reduction of nitrates & phosphates and the denitrification of nitrates to elemental nitrogen. So let’s start with this topic.

My tank was initially cycled using Prodibio Biodigest bacteria + market prawn as the ammonia source. Completed the cycle in about 2 weeks (Cycling started Oct 17. Live stock added 2nd Nov)

image.jpeg.c797bb19b7ef4c26f550d5b88494e334.jpeg

Link Refer to this link for that post

The tank is coming to 6 years & has been relatively problem free. In the past few months, i added ~ 10 fish and also about 10 non photosynthetic corals. Whenever new fish are added, I’ll feed a little more in the initial weeks (Aside from the default morning & night feeding)  I’ll add additional frozen food feeding in the afternoon & evening. With the non photosynthetic corals, I now feed Reef Roids twice a day.

With the heavy feeding regime, nitrates & phosphates started to creep up & more algae started to form on the rock. I worry about old tank syndrome.

I’ve been dosing Prodibio Biodigest on regular basis even though its an established tank - to maintain the biological filtration balance & reduce nitrates/phosphates. And to step it up, recently, started to supplement with Biotim, Probiotix & Reef Booster with good results. Nitrates/phosphates back under control. And corals/fish are looking happy.

  • Biodigest – bacteria source
  • Biotim – enzymes & bacteria food
  • Probiotix – additional bacteria set to complement Biodigest to enhance biological filtration
  • Reef Booster – Liquid food for corals, invertebrates & fish
  • Coral Vits - Vitamins

image.jpeg.023b651fb8ecf100d092714956113179.jpeg

image.jpeg.392563ba7a7bbdc17fb1e090177e5981.jpeg

My process : Dose Biodigest, Biotim & Probiotix after water change. These are bacteria related or complement each other. Turn off the UV sterilizer for the day to let the bacteria settle in.

 

 

 

Daytime pic with yellow lens :

image.jpeg.9735e272a8b692d3705a51e495fc2301.jpeg

 

Daytime pic with yellow lens :

image.jpeg.71df564405d8ec5a41b7ab3b49335771.jpeg

image.jpeg.21fc69c107217d6ec2f8a629d77c7712.jpeg

 

My process for Reef Booster (liquid food) though its not stated in the instructions, dose it at night just after lights off. The skimmer may overskim for a while. So I’ll typically open up the skimmer gate fully for the day. So it’ll still oxygenate the water but won’t overflow.

Below is a consolidation of information found on the web + some of my inputs.
 

Biodigest

Biodigest is fundamentally a hyper concentrated mixture of various bacteria strains.
One important advantage is Biodigest (and many Prodibio products) come sealed in a argon filled ampoule (Wiki : Ampoule = small sealed vial used to contain a sample. Usually made of glass). Argon is an inert gas. Without the presence of oxygen, the bacterial remains dormant until the liquid is put in tank water. The dissolved oxygen then awakens the dormant bacteria. As such, the bacteria does not have an expiration date & can be stored even in room temperature for a very long time (supposedly >5 years!) => 100% potency when used. I didn’t understand the concept of dormancy until someone used the analogy of baby brine shrimp eggs in dormant state which hatch when exposed to water. Storing the bacteria in an ampoule avoids the issue with “Bacteria in a Bottle” where the bacteria is known to degrade over time when exposed to air after opening.

The nitrogen cycle (toxic Ammonia -> Nitrites -> Nitrates) requires a mixture of bacteria strains to complete the entire process. Some heterotrophic  strains start the conversion process (eg Nitrosomonas europaea from ammonia to nitrite), then hand off to other strains of bacteria to take on the next stages and so forth and finally finish the nitrogen cycle (eg Nitrobacter winogradskyi from nitrite to nitrate). According web information, Biodigest contains various live bacterial strains of the right proportions to perform the above. Biodigest also contains Paracoccus denitrificans & Pseudomonas stutzeri  – strains that can convert nitrates to elemental nitrogen under anaerobic conditions (i.e. living in your bio media to reduce nitrates)

(Heterotrophic definition : capable of utilizing only organic materials as a source of food)
 

 

About dosing in an established tank.

Over time, some strains will die off. Some strains will dominate. Some mutate This may reduce the effectiveness of your biological filter over time. There is mention that over time, a dominant strain will emerge – something known as a “mono culture”. Anecdotally, this could be the trigger for cyano or nuisance algae even in established tanks. To prevent this, its  best practice to dose Biodigest every 2 weeks to maintain optimal purification proportions of key bacteria strains.

Other times to dose Biodigest is during nitrate surge events –  adding new fish, fish/coral death, after cleaning sand bed or after water change etc.
 

Biotim
Simply put, Biotim adds micro nutrients to the tank, which Biodigest (bacteria) consumes. And also contains other content that is beneficial for livestock.  

This is a summary of what I found online : Contains selected amino acids, enzymes, vitamins (including riboflavin = Vitamin B2  - involved in conversion of food to energy, metabolize fats & proteins). Also contains trace elements generally useful for livestock – Sulfur for proteins, iron for plants & fish blood, cobalt for Vit B, Boron for cell building etc. On the whole, Biotim affects cellular bioactivators (definition : A bioactivator is a biologically active (bioactive) material which is able to decompose agricultural solid wastes). It accelerates the digestion of organic matter. You can observe this if you have an ORP meter to monitor your tank’s redox potential. By increasing the number of bacteria in the population,  you improve the rate of nitrate/phosphate reduction & ultimately improve water quality.
 

 

Probiotix

This is a relatively new product (introduced in 2017). Probiotix contains strains of bacteria different from those of BioDigest. 

The diversity reinforces the crucial phase of the nitrogen cycle and is more flexible and better able to adapt to varying conditions (eg. Temp, pH etc)

image.jpeg.8a6a6668f883e102bb286571132b264d.jpeg

 

Reef Booster

A complete nutrient supplement for corals, invertebrates & fish. Helps reduce nitrates & phosphates by feeding anaerobic bacteria in sandbed/rocks/bio media.
Contains phospohlipds,  amino acids, omega-3 marine fatty acids, vitamins, carotenoids.

 

Let’s understand what some of these are for :

Phospholipids - major components of the cell membrane and also provide a fluid character to the membranes.
Fatty acids - integral part of cell membranes throughout the body and affect the function of the cell receptors in these membranes.


Specific to Omega 3 - Studies have shown that fish develop stronger heart muscles and healthier circulatory systems. This results in lower mortality and less disease, as well as improved fillet quality. 


The most common diseases are due to parasites that they may carry within and outside their bodies, causing issues such as infection or inflammation. Omega3 reduces inflammation and hence reduces the risk of serious infection. By reducing inflammation, they recover quicker.

Shake the vial thorough before use & pour into a high flow area. It turns the water cloudy for a while. Instructions mention to turn the skimmer off to prevent it from overflowing. But personally I just open the skimmer gate valve fully for several hours.
 

Caratenoids : Beneficial anti-oxidants that can protect one from disease & enhace the immune system

image.jpeg.285c7d2906bd5ac8df3be282032479cc.jpeg

Shake the vial thorough before use & pour into a high flow area. It turns the water cloudy for a while. Instructions mention to turn the skimmer off to prevent it from overflowing. But personally I just open the skimmer gate valve fully for several hours.

image.jpeg.7ca331fee397a32b144a77e021a111fd.jpeg

 

 

Coral Vits

Corals, fish & invertebrates require vitamins for proper cell function. Some organisms can synthesize vitamins but not in sufficient quantities & hence need to be supplemented.
Coral vits contain water-soluble vitamins (B1, B2, B3 (or PP), B4, B5, B6, B7, B8 (or H ), B9 (or Bc), B12) and fat-soluble (A, C palmitate, D2, D3, E, K1, K2 and K3)
To be used with Reef Booster dosing regime. Either together or alternate weeks. (once every 2 weeks)


image.jpeg.66bb2f4c3422163da59f13495781e273.jpeg

 

 

Biokit Reef
To keep things simple, Prodibio also has an all-in-one pack called Biokit Reef
Contains 5 items : BIODIGEST, BIOPTIM, REEF BOOSTER, IODI+, STRONTI+

image.jpeg.9d4dbed7f7168b70336befc497215ee8.jpeg

 

Iodine is one of the most important trace elements. In fact this is one of the elements that I also measure on a regular basis with home test kits.
Low iodine will result in dull tissue & more susceptible to parasite attacks (eg. Less resilient to Acro eating flatworms).

Strontium is a macro element that is quite close to Calcium. It supports growth of stony coral skeleton. Low strontium will result in slow growth. Brittle skeleton.
Good levels will show up as increased growth rate/encrustation & thicker/sturdier SPS branches
 

 

 

A long post but to sum it up :

image.png.221acea0dc102e02aacc213874c93985.png

 

image.jpeg.f4fde359847aa5471f35bf63f64435a7.jpeg

 

Batch information for traceability. Made in France

image.jpeg.f38f8419ae02f74cf58392231983006e.jpeg

 

Restocked recently

image.jpeg.2de8237f8add4f10f6003886dc6c4547.jpeg

 

  • Like 1

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • SRC Supporter

For those who are not aware, Apex released a new firmware for the FMM module to add support for the new fancy liquid level sensors. And for immediate practical reasons, enabled a buzzer alarm on the FMM module.

578329652_fmmupdate2.JPG.d1fe81b5188f2013116d3b5c6ed2b5d8.JPG

 

Software release notes

1865197726_FMMupdate.JPG.53a07d0a3b79154a33ecfabc52a4c46a.JPG

 

On my tank system, I used to have a red LED to notify me when things need attention. Recently I added an addiitonal orange LED as well. And now with the FMM buzzer, its able to provide better feedback on the level of urgency to attend to the tank.

 

IMG_0025.jpeg.f9084826a17cdbced3124e0685896346.jpeg

  • Red LED + Orange LED = (1) temperature too low/high, (2) CO2 tank empty
  • Red LED = (1) ATO empty, (2) Skimmer bucket is full (skimmer stop), (3) Sump water level low 
  • Red LED + Buzzer = Water Leak!!
  • Orange LED = (1) Skimmer is off,  (2) Skimmer waste bucket quite full

 

With the FMM alarm feature, a new outlet called Sound_Alarm is added to the dashboard.

image.jpeg.d040cad3e35ead4b28d493a3d0a06fd9.jpeg

 

 

 

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • 2 weeks later...
  • SRC Supporter

Got an Apex PMK (PAR measuring kit) recently. Now able to measure PAR throughout the day. Also with the ASM module that comes in the kit, its now possible to integrate other commercial sensors to the Apex.

First, some terminology :

PAR stands for “Photosynthetically Active Radiation”’ and refers to the wavelength of light that is used for photosynthesis. Typically between 400nm to 700nm of the light spectrum

PPF (Photosynthetic Photon Flux ) is the term used to define the measurement of PAR over a period of 1 second. Unit of measure is μmol/s (read as micro mole per second)

Strictly speaking, what we measure with the PAR meter is PFFD (Photosynthetic Photon Flux Density) – which is PPF over a specific area. Unit of measurement is μmol/s/m2. (read as micro mole per second per square meter)

Old PAR measurements from this post https://www.sgreefclub.com/forum/topic/142862-my-slice-of-nature-part-3/?do=findComment&comment=1963038337921396_20220213_091534586_iOSa(Large).jpg.c8917a44a85ca1551bded5734ccbcc91.jpg

 

 

With the PMK, we can use the data to easily calculate DLI (Daily Light Integral) – total PFFD over a 24 hour period. Some setups have higher powered lights capable of reaching very high PAR & vice versa. Hence it is useful information to help tune high PAR settings to shorter lighting period. Or low PAR but longer lighting period. Unit of measure for DLI is mol/day. Will post more about this later on.

 

image.jpeg.14f591a1d3f676fc5557b0d885c27825.jpeg

 

Main items : ASM module, an Apogee quantum sensor, a ceramic rock with compartment to hide the Apogee sensor,  Aquabus cableimage.jpeg.26429a62e42d7c27937a4b516b5e3c38.jpeg

 

The ASM also has an I/O port to hook up another breakout box and temperature module.

image.jpeg.94ea02c930cd335fa995a4932ef28e43.jpeg

 

The Apex version of the quantum sensor has a plastic body and designed to be left in the water for extended periods of time.

image.jpeg.627c27f21e1214b9b5500ef944c74369.jpeg

image.jpeg.d9393d98448bd5dc936170be33e0ac65.jpeg+

 

81182122_P1010302(Large).JPG.13a6ecbd4708b9f3eaa1bc56cec84ac7.JPG986121230_P1010301(Large).JPG.3216ce38197aa2a3c8a5ea67c689b1f1.JPG

 

An example of the PAR readings at this section near the Acanthophyllia(Prata) corals.

image.jpeg.ce01a5681de58f8fa2e1b8b8e1e0dbee.jpeg

 

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • SRC Supporter

Totally lost track of the last time the water filter filters were changed.

  • RO membrane last changed ~ October 2016. Decided to change it after finding the TDS after the RO membrane is in the 18ppm range.
  • Carbon & sediment filter probably 18 months ago. Ideally I should change them every 6 months to 1 year. Quite important to ensure the carbon filter are not depleted else chlorine will simply pass through the carbon filters. This will deplete the DI resen very quickly ($$$)

 

Based on rough count, i use about 300L of clean water a month for water change & evaporation top up.

The filter produces about 200L waste water. So in total about 500L passes through the carbon/sediment filters per month. Or about 3000L in 6 months.

 

1960096935_P1010314(Large).JPG.4295377bce7fda814a7f84e470dac45c.JPG

 

Configuration :

Water inlet -> Carbon filter 1-> Carbon filter 2 -> Sediment filter -> Booster Pump -> RO membrane -> DI resin 1 -> DI resin 2 -> Water outlet

After swapping out the filters, i disconnected the hose after carbon filter 2 to let the carbon flush out. This is how much carbon dust comes out for the initial 5L of water

IMG_0137.JPEG.93fbd57964a179a0fad9338c7d5134fd.JPEG

IMG_0140.JPEG.7bc52e8cb08ab4dfee845f09848276ff.JPEG

 

After 10L

IMG_0146.JPEG.837a4cc34912e01834e21f3ef85056a1.JPEG

 

After 20L.  All clear! Then attach the sediment filter back to the system.IMG_0149.JPEG.83b46c41b1260efd96114bc19bb28002.JPEG

 

With the RO membrane also replaced, TDS readings i'm getting are

Water inlet ~ 67 TDS

After RO membrane ~ 3 TDS

After DI resin ~ 0 to 1 TDS

 

 

 

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • SRC Supporter

A fellow reefer recently asked about what I used to clean the glass.

Main magnetic cleaner is this DD Blade Runner. Note there are 2 versions - Standard & Strong (depending on your glass thickness). My tank is 15mm glass - so I got the "strong" version for 15-20mm glass. Very strong magnet so fewer passes are needed. And it does not have a scrubber on the inside so there is little risk of sand getting trapped => little risk of scratching glass.

954075450_IMG_0342(Large).JPEG.c9e404e9f2b75d03812d8f431e5665de.JPEG

 

Very thin profile. Good for those cramp sections.

image.jpeg.e2b6545e7b85f158bea3a7963cb6cb4a.jpeg

 

For difficult to reach places or where manual scrubbing is needed, the best one i've used so far is the Seachem Algae Scraper. Using it since March 2020. Still on the 1st blade. Full plastic handle. And almost no rust on it. Its not cheap but well worth the $$. Be careful of those manual glass cleaner you buy from taobao or LFS that use a metal handle. It'll rust internally and leach bad stuff into the tank.

112141838_IMG_0345(Large).jpg.21d05f45c3cd6869d151d052870b192a.jpg

 

Externally, just use a dedicated wet cloth for cleaning glass. Then squeegee of with Ikea LILLNAGGEN Squeegee

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • SRC Supporter

Working to reduce phosphates down to the 0.1ppm range. Currently climed to 0.3ppm

IMG_0355.JPEG.bb8e9043d6d977a6b07560dee719efbb.JPEG

 

IMG_0360.JPEG.fdbf55b575265774dfa8eef40454dc69.JPEG

 

Rinse by pouring water down the Torqimage.jpeg.4db01aade7243372a869860c3a1f76eb.jpeg

 

All clear after a few rounds.

image.jpeg.feb30aa1e09520beda081871b67dd6ff.jpeg

 

Sponge is cleaned weekly.image.jpeg.0df5b8b791c0da94d96759080163f331.jpeg

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • SRC Supporter

It is well known that different testers/test kits will produce slightly different results. Its nice to have it all aligned to a single number (though it really does not matter in the big scheme of things) since we are really checking for big deviations.

 

In any case, I got some bad advise that its OK to calibrate the Trident by inputting manual measurement numbers (eg. readings from Salifert manual testing). End up getting haywire readings  for Ca, Mg, KH

Best solution is to calibrate with the calibration solution provided.552906001_P9180061(Large).JPG.bd4f3a9698cfd7806bea77bfae289611.JPG

 

See the difference before/after using the the calibration solution. All good now.

1632987221_TridentCalibration.JPG.4e309f562d7a1b6ec4a3ff0ad2f5652b.JPG

IMG_0173.PNG

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • 3 weeks later...
  • SRC Supporter

Some random pics from the last week..

Starry Blenny hanging out at the wavemaker. Time to give the Vortech a quick scrub.

image.jpeg.37a364d2a716aec75f22c3c63a6a1809.jpeg

 

Hosting this pectinia for a fellow reefer till his tank is ready. Hmmm....not sure if he remembers its still with me.

image.jpeg.461e3e01d5a292aa5843112cd25b919d.jpeg

 

Dosing regime of bacteria & supplements every 2 weeks. This helps provide some confidence to improve nutrient & bio filtration performance of the tank.

image.jpeg.a6c73286b20fab3e1082f850ff8e52be.jpeg

 

Refer to my earlier post on 4th Sept on the writeup.

  • Biodigest – bacteria source
  • Biotim – enzymes & bacteria food
  • Probiotix – additional bacteria set to complement Biodigest to enhance biological filtration
  • Reef Booster – Liquid food for corals, invertebrates & fish
  • Coral Vits - Vitamins

 

 

 

 

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • SRC Supporter

CO2 scrubber. Best to get those color changing type, so you'll know when they are depleted.

I had some cheap Taobao media on hand. They claim to be color changing but apparently don't. Not even sure if they work or not.

 

1914075895_IMG_0855a(Large).jpg.e30fefbe5c6f142804397e5e3b37d407.jpg

 

The one i'm using is TLF CDX

IMG_0518.jpeg.896dbe94a34da68423d54306137ee2df.jpeg

 

IMG_0514.jpeg.712b65b448eab4d0b802616c8323d439.jpeg

 

This is the tank pH difference. Roughly 0.1pH increase.

1318215002_ApexPHcharta.jpg.a01be00f9f149a0cf6365dd75e67edb2.jpg

 

 

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • SRC Supporter

Several weeks back, a fellow reefer asked me recently on my opinion between the Apex Sky vs Aqua Illumination Hydra. That query piqued my interest on the Sky. I managed to get hold of a used SKY.  A short review here. 

Key take away from specs point of view :

 

Hardware setup is very easy. The mounting points make use of Ecotech Radion mounting kits. The screw widths are the same width as the AI Hydra, so the slide into my light stand directly (no mounting kit required).

image.jpeg.746658e4191b922dd4e7e10b3abeced3.jpeg

 

Cable is 3m long to connect to the Mean Well power supply.  For those who are not aware, Mean Well power supplies are reputed to be of better quality & reliability

image.jpeg.c30b022879a9fc8705d3f295bc530e90.jpeg

 

Some screenshots of the templates available :

image.png.e5e6895ba975accd51154086b697f172.png

image.png.ad0acfc332678d3951415e8b32cbed89.png

 

Templates are always good to have. Easy to switch switch. Then just set the brightness power percentage. The light adjustments are clustered around 4 groups. 

  • Channel 1 - Amber 
  • Channel 2 - Violet 
  • Channel 3 - Royal Blue
  • Channel 4 - White

 

Some comments on the templates & settings available :

  • Neptune Sky : around 20k color setting but less blue.
  • Coral Growth : max of all 4 groups. Max PAR
  • Photo mode : 40% on channel 1-3. 100% for White
  • SPS AB+ : Emulates the famous setting from Ecotech Radions
  • SPS PHX14+ : Emulates the 14k spectrum of Phoenix Metal Halide lamps
  • ATI Blue Plus : Emulates the very popular ATI Blue Plus HO Flurorescent bulbs
  • Several preset color temperatures fromn 5K to 20k
  • You can turn on the cloud cover feature if you are worried about burning your corals

image.png.7f229df9d2dabf50787662d585deb8c7.png

 

image.png.47e8f2cf0219ef3524c94b20a56414f1.png

 

Configuration interface when using PC.

image.png.ed09700cda543b7a0c63dfa9a2413401.png

 

View on the mobile app. 

 

image.png.7a166abe6d9180e715633dcc18f61b37.png

 

Current setup. A blanket of light above the SPS. 

image.jpeg.b9718d14040f3b98171c1e8e9f96feb8.jpeg

 

Plan to measure the PAR during the week. A sample check at intermediate power setting made today.

923854172_IMG_0827(Large).JPEG.536a501169173082d9f69954139fbad0.JPEG

 

 

 

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • 2 weeks later...
  • SRC Supporter

Decided to print a PAR meter holder so it hands on the edge of the aquarium. Easier to snap a photo of the reading for record purposes. Easier than writing on a piece of paper.

image.jpeg.86a3ac5424cd985bc1b602fa6c9c2fd9.jpeg

image.jpeg.d70ea01a1ed762173240578daaadb6f0.jpeg

 

The orange font shows the PAR readings at 2pm.

The blue font shows the evening to night PAR readings when the lights are Blue & Royal blue.

Picture taken at night with yellow lens. So ignore the double image of the lights (due to internal reflection of the dual later yellow lens + polarizer)

image.jpeg.acbdec78e52fcf0f89d4bf623e24b29f.jpeg

 

The Apex Sky provides a blanket of light to the SPS  section. Love it!

Peak setting is 70% intensity.

image.png.6d4b9b6feb3feb93164132aafd046a06.pngimage.png.6c98a4ad7297a40544e154064e4162ee.png

 

 

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.




×
×
  • Create New...