Jump to content

Help with Bubble Magus Curve 5 Issues!


nwyk153
 Share

Recommended Posts

I recently bought this Curve 5 Skimmer from Ng yesterday. As soon as i went home, i set it up and run the skimmer in my sump. It was skimming normally and produced nice foam for the past 12 hours. After that it starts to overflow and fill up the cup. I switched off the skimmer, took the cup out and empty it.

By the time i put it back and turn the skimmer back on, i can see that the water level inside the skimmer is not constant. It goes up and down. I tried to play around with the adjust tube to no avail. So i took everything apart and clean it, including the pump.

After assembling it back together, the skimmer still performs abnormally. The water will not stay on the level i adjusted. It will go up and down the entire hour.

IMG_3240.mov

Is this normal for a new skimmer? If not, should i return it back?

Reefing since 2003
 4ft x 2ft x 2ft Mixed Reef (BB):-
50 Gal Sump,

Apex Controlled System (Lab grade),
Deltec SC1455 Protein Skimmer,
Vortech MP40wQD,

Jebao RW-15

Maxspect Razor 320w
Eheim 1260 Return Pump,
Hailea HS-66A 1/4HP chiller,
TLF Reactor 150, running HydroCarbon 



 

Link to comment
Share on other sites

it was sitting inside a sump with a 9" water level. If i dial it towards minimum, it will start to overflow and then the water inside the skimmer dropped. And then it went up again>overflow a bit> went back down again>repeat. Tried everything from cleaning the air tube to the water pump and the skimmer's body. I also make sure the output of the pump is not aim directly towards the plate holes. At lost here.

Not sure if the ng couple accept 1-on-1 exchange.

Btw, anybody has the contact no. for Ng shop?

Reefing since 2003
 4ft x 2ft x 2ft Mixed Reef (BB):-
50 Gal Sump,

Apex Controlled System (Lab grade),
Deltec SC1455 Protein Skimmer,
Vortech MP40wQD,

Jebao RW-15

Maxspect Razor 320w
Eheim 1260 Return Pump,
Hailea HS-66A 1/4HP chiller,
TLF Reactor 150, running HydroCarbon 



 

Link to comment
Share on other sites

yea, i've tried raising my water level up to 11" earlier. The water is still not stopping at the level i adjusted. A very odd behaviour for a skimmer. My best guess the pump is faulty. Will give it 24hr to run. If its still behaving oddly, will try to bring back to the shop.

Reefing since 2003
 4ft x 2ft x 2ft Mixed Reef (BB):-
50 Gal Sump,

Apex Controlled System (Lab grade),
Deltec SC1455 Protein Skimmer,
Vortech MP40wQD,

Jebao RW-15

Maxspect Razor 320w
Eheim 1260 Return Pump,
Hailea HS-66A 1/4HP chiller,
TLF Reactor 150, running HydroCarbon 



 

Link to comment
Share on other sites

  • SRC Member

yea, i've tried raising my water level up to 11" earlier. The water is still not stopping at the level i adjusted. A very odd behaviour for a skimmer. My best guess the pump is faulty. Will give it 24hr to run. If its still behaving oddly, will try to bring back to the shop.

Bro I had the same issue initially. What works for me was i removed the red cap at the bottom of the skimmer to release the water pressure.

Once u remove the cap. Make sure u increase the water level to just below its neck. Give it a couple of weeks to break in and everything should be fine.

Link to comment
Share on other sites

Bro I had the same issue initially. What works for me was i removed the red cap at the bottom of the skimmer to release the water pressure.

Once u remove the cap. Make sure u increase the water level to just below its neck. Give it a couple of weeks to break in and everything should be fine.

Hows your Curve 5 now? Did you managed to put the red cap back after it broke in?

Reefing since 2003
 4ft x 2ft x 2ft Mixed Reef (BB):-
50 Gal Sump,

Apex Controlled System (Lab grade),
Deltec SC1455 Protein Skimmer,
Vortech MP40wQD,

Jebao RW-15

Maxspect Razor 320w
Eheim 1260 Return Pump,
Hailea HS-66A 1/4HP chiller,
TLF Reactor 150, running HydroCarbon 



 

Link to comment
Share on other sites

Mine is the curve 9. I didnt put it back in and just leave the cap at the side. Been running fine for 2 or 3 mths

The skimmer is still not in constant water level after i took out the red cap. #annoying as f**k. Sigh. I'll just wait it out then. Thanks for the help.

Reefing since 2003
 4ft x 2ft x 2ft Mixed Reef (BB):-
50 Gal Sump,

Apex Controlled System (Lab grade),
Deltec SC1455 Protein Skimmer,
Vortech MP40wQD,

Jebao RW-15

Maxspect Razor 320w
Eheim 1260 Return Pump,
Hailea HS-66A 1/4HP chiller,
TLF Reactor 150, running HydroCarbon 



 

Link to comment
Share on other sites

  • SRC Member

The skimmer is still not in constant water level after i took out the red cap. #annoying as f**k. Sigh. I'll just wait it out then. Thanks for the help.

Try turning the tube at the side to adjust. It might help too. Good luck!
Link to comment
Share on other sites

update: Curve 5 skimmer is skimming normally the whole day today. But it will stop skimming for 2 hrs if i feed my fish. I guess that is normal(?)

Reefing since 2003
 4ft x 2ft x 2ft Mixed Reef (BB):-
50 Gal Sump,

Apex Controlled System (Lab grade),
Deltec SC1455 Protein Skimmer,
Vortech MP40wQD,

Jebao RW-15

Maxspect Razor 320w
Eheim 1260 Return Pump,
Hailea HS-66A 1/4HP chiller,
TLF Reactor 150, running HydroCarbon 



 

Link to comment
Share on other sites

  • 2 weeks later...

Whats ng couple shop? I heard many times but not sure which shop ah

It's the one infront of AH Beng.

Reefing since 2003
 4ft x 2ft x 2ft Mixed Reef (BB):-
50 Gal Sump,

Apex Controlled System (Lab grade),
Deltec SC1455 Protein Skimmer,
Vortech MP40wQD,

Jebao RW-15

Maxspect Razor 320w
Eheim 1260 Return Pump,
Hailea HS-66A 1/4HP chiller,
TLF Reactor 150, running HydroCarbon 



 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share



×
×
  • Create New...