Jump to content

Cube 7


sherman
 Share

Recommended Posts

The Light up finally

post-669-068679300 1287292462_thumb.jpg

6.5 * 2 * 2 + 3.75 * 1.5 *1.5,(Decomn on 14/9/08)
4*2*2 + 2.5*1.25*1.25 (Decomn on 1/8/09)
5*2*2 (Fully LED light system, 140 3 watt SSC leds with 60 degree lens)(Decomm)
2.5*2*2(Fully LED Light System,96 3 watt SSC leds with 60 degree lens)(Decomm)

5*2.5*2(LED only)

Eheim return 1 * pump

1 HP Daikin compressor with cooling coil
2 Jebao OW40, 1 ecotech MP40,
1X6085 Tunze wm,

1 CURVE 7 Skimmer

  1 DIY 80 led control by Bluefish mini 

1 radion XR30W G2, 2 Radion XR15G3

Sump area lite by 5 ft T5 , 6 * SSC 3 watt red LED for refugium

1 Full spectrum E27 led light

1 CR control by bubble count

Start No Water Change since 1st Dec 2016

Add new 2.5x2x 1.5 ft 

 nLekOfpYts.jpg
[/quote]


 

Link to comment
Share on other sites

  • Replies 104
  • Created
  • Last Reply

Top Posters In This Topic

Top up the tank with water from my 5 footer and start cycling

before put on the modified LED light cover

post-669-055713200 1287322901_thumb.jpg

6.5 * 2 * 2 + 3.75 * 1.5 *1.5,(Decomn on 14/9/08)
4*2*2 + 2.5*1.25*1.25 (Decomn on 1/8/09)
5*2*2 (Fully LED light system, 140 3 watt SSC leds with 60 degree lens)(Decomm)
2.5*2*2(Fully LED Light System,96 3 watt SSC leds with 60 degree lens)(Decomm)

5*2.5*2(LED only)

Eheim return 1 * pump

1 HP Daikin compressor with cooling coil
2 Jebao OW40, 1 ecotech MP40,
1X6085 Tunze wm,

1 CURVE 7 Skimmer

  1 DIY 80 led control by Bluefish mini 

1 radion XR30W G2, 2 Radion XR15G3

Sump area lite by 5 ft T5 , 6 * SSC 3 watt red LED for refugium

1 Full spectrum E27 led light

1 CR control by bubble count

Start No Water Change since 1st Dec 2016

Add new 2.5x2x 1.5 ft 

 nLekOfpYts.jpg
[/quote]


 

Link to comment
Share on other sites

  • 4 months later...
  • SRC Member

Hi Sherman,

With the exhaust fan pulling out warm air from the LED assembly, it seems that moist air under the hood tends to be sucked into the LED assembly. Would it be better to drill a few small holes on the plastic hood to allow dryer air to enter into the assembly?

Any update pics of your Cube 7 with corals?

:thanks:

Link to comment
Share on other sites

The clear cover below the hood need to be properly seal.

If the seal is broken then air from the water surface will be

suck into the hood.

So far I have not face water vapor in the led area for this

cube 7

6.5 * 2 * 2 + 3.75 * 1.5 *1.5,(Decomn on 14/9/08)
4*2*2 + 2.5*1.25*1.25 (Decomn on 1/8/09)
5*2*2 (Fully LED light system, 140 3 watt SSC leds with 60 degree lens)(Decomm)
2.5*2*2(Fully LED Light System,96 3 watt SSC leds with 60 degree lens)(Decomm)

5*2.5*2(LED only)

Eheim return 1 * pump

1 HP Daikin compressor with cooling coil
2 Jebao OW40, 1 ecotech MP40,
1X6085 Tunze wm,

1 CURVE 7 Skimmer

  1 DIY 80 led control by Bluefish mini 

1 radion XR30W G2, 2 Radion XR15G3

Sump area lite by 5 ft T5 , 6 * SSC 3 watt red LED for refugium

1 Full spectrum E27 led light

1 CR control by bubble count

Start No Water Change since 1st Dec 2016

Add new 2.5x2x 1.5 ft 

 nLekOfpYts.jpg
[/quote]


 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share




×
×
  • Create New...