Jump to content

Review: Bubble Magus Curve 180 Skimmer


peacemaker
 Share

Recommended Posts

  • SRC Member

I bought the above skimmer recently, and decided to share a simple review. Do pardon me on the bluish pics as they were taken pretty near my tank when the lights were switched on. :paiseh:

The Bubble Magus Curve 180 is an in-sump skimmer that runs on an AquaBee 2000 needle wheel pump. This is the only difference compared to the Curve 7, which runs on the Rock pump, most likely a house brand.

Below are some shots during un-boxing. Basic packing requirements like foam to keep the product from knocking all over, and individual plastic wraps for every part. Comes with a one page assembly manual and a QA certificate of approval.

post-13914-0-06812400-1334334850.jpg

post-13914-0-45910800-1334334860.jpg

post-13914-0-03019100-1334334870.jpg

post-13914-0-82228800-1334334879.jpg

Link to comment
Share on other sites

  • SRC Member

A display of all the parts. The skimmer body is very well built and feels solid. It wasn't as curvy as expected (you know, having the name of Curve 180, you tend to expect something very shapely... :P ), but in general, you could say that a slight curve is present.

The next thing that caught my attention was the base plate. It has 4 'shark fin" looking catches that locks the skimmer body in place, making it a whole lot easier to remove and clean. Looks pretty neat in white and red, like a fat shuriken.

post-13914-0-01120900-1334335541.jpg

post-13914-0-70065200-1334335551.jpg

post-13914-0-88622600-1334335563.jpg

post-13914-0-03736800-1334335571.jpg

Link to comment
Share on other sites

  • SRC Member

The pump is secured to the base plate, followed by a leading box (or some may call it, a bubble plate) with nylon screws. They provided an option to switch the location for the air intake kit by making 2 holes 90o of each other on the skimmer body.

Instead of a rubber seal for previous models, the Curve 180 uses an 'O' ring for the skimmer cup. It was a little dry, so I had to coat it with a bit of grease, in this case, Vaseline.

post-13914-0-97177100-1334336136.jpg

post-13914-0-25554900-1334336153.jpg

post-13914-0-54133000-1334336167.jpg

post-13914-0-74510000-1334336179.jpg

Link to comment
Share on other sites

  • SRC Member

I liked how the model of the skimmer is etched onto the cover instead of some cheap sticker. They added a button at the bottom of the skimmer cup cover, which helps in the displacement of the organic waste into the skimmer cup. The usual drain elbow is present at the bottom of the waste collection cup.

They added a red cap on the water output adjustment tube for better grip. Muffler is secured just beside it.

post-13914-0-09478900-1334336948.jpg

post-13914-0-48476200-1334336958.jpg

post-13914-0-98203800-1334336969.jpg

Link to comment
Share on other sites

  • SRC Member

Now, for performance. First 2 photos are taken in less than an hour of starting the skimmer. The next 2 photos are taken 3 days later. (I actually wanted to take a photo the next day after starting the skimmer, but silly me, forgotten to seal the drain outlet, so wasted skimming for a day -_- )

post-13914-0-40063300-1334337365.jpg

post-13914-0-56497000-1334337374.jpg

post-13914-0-99269900-1334337384.jpg

post-13914-0-82084200-1334337394.jpg

Link to comment
Share on other sites

  • SRC Member

My tank is approx. the volume of a 2ft cube, and there are 6 nano fishes, 2 crabs and a fire shrimp. I feed them about 5 times a week with a mix of mysis, pellets and cycopeeze, so this gives you a rough idea of the bio load.

In summary, I'm satisfied with the performance so far, and hope that it will continue to serve me well. Pls feel free to post any questions here, and I'll try my best to answer them.

Cheers! :cheers:

Link to comment
Share on other sites

  • SRC Member

Can pm me the price.tks

-Main Display Tank : 2ft x 1.5ft x 1.5ft c/w sump tank cabinet (Set up by aquarium artist)

-Lightings : 4 sets of 1.5ft mini aqua lumen LED lights (7 high power led 15W)

-Chiller: 1/4HP artica chiller with a standby of HC-100A

-Skimmer : Bubble Magnus 3 (cone)

-Phosphate Reactor

-NP Bio-pellet D&D onceanic hang-on reactor

-Wavemaker : MP10

-Temperature mointor : American Wireless pinpoint thermometer

Link to comment
Share on other sites

  • SRC Member

I was actually afraid that it will turn out like that, that's why I opted for a reputable pump instead. Looks like the choice paid off. There must be a reason why Deltec skimmers chose AquaBee pumps before they came out with their own. ^_^

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share



×
×
  • Create New...