SRC Supporter SubzeroLT Posted April 29, 2020 Author SRC Supporter Share Posted April 29, 2020 I've decided to drop the idea of the floating thermometer & go with a way to water proof the top of the probe by encasing it in a tube. Will post pics later as the glue on the assembly is still drying. In any case, this is what the inside of the Apex temperature probe looks like. Its looks quite robust but one will never know the longer term effect of continuous exposure to salt water. Quote Facebook : https://www.facebook.com/mysliceofnature/ Link to comment Share on other sites More sharing options...
SRC Supporter SubzeroLT Posted May 1, 2020 Author SRC Supporter Share Posted May 1, 2020 Quick iphone pics from today Side view Following up on the Apex temperature probe. This is what the final implementation looks like. 3D printed tube mount (left side for sump level float switch). Right side to hold the Apex temperature probe. Using the dremel to cut & later grind off the plastic pipe to ensure a perpendicular cut Installed in sump It works This resolves the issue where temperature probe is out of water when excessive water is removed (eg. water removed when fragging or acclimatizing fish). And yet ensures the tip part is not under water when the return pump is off. 3 Quote Facebook : https://www.facebook.com/mysliceofnature/ Link to comment Share on other sites More sharing options...
SRC Supporter SubzeroLT Posted May 2, 2020 Author SRC Supporter Share Posted May 2, 2020 A nice video from Reef Builders about the Versa peristaltic pump From using other peristaltic pumps at work, there are a couple of concepts that's applicable to us hobbyist for any kind of peristaltic dosing pump : There is a short break in period for tubes (typically a few minutes of continuous use). After the break-in period, flow & volumes will be more stable. We typically calibrate the pump upon 1st installation. It is best practice to re-calibrate it, say, 1-2 weeks later due to this 'break in' period. Calibration is ideally done at the final flow rate you are running it at and over as large a volume as possible. Both possible with the Versa & Mobius app. My unit has been running well since it has been set up. I opened mine up to have a better look at it and to understand the product a little better. Planetary gear assembly. Great build quality. From the back. Proprietary pancake stepper motor. And the circuit board on the left. Quote Facebook : https://www.facebook.com/mysliceofnature/ Link to comment Share on other sites More sharing options...
Wai6866 Posted May 5, 2020 Share Posted May 5, 2020 Bro, the calcium reactor feed pump and main pump is it on 24hr? I'm using a Skimz CM152 calcium reactor. An affordable & reliable model. #supportlocal There are many methods to tune the CR. My process parameters are : pH ~ 6.52 CO2 timing : 24hrs Effluent flow rate : 140cc/min Bubble count tuned to meet the above Media : Grotech Rowalith + ~30% Grotech Magnesium Pro Target parameters : Ca: 400, Mg : 1400, KH : 8.3 As with most CR media brands (Grotech Rowalith, Caribsea ARM, TLF Reborn), it provides mostly Ca, KH only. In order to supplement magnesium, one should add some Magnesium media. Popular brands are Grotech Magnesium Pro & TLF ReMag. Suggest to start with 10% Mg media first. If its not able to maintain Mg levels with respect to Ca, KH, then just add more Mg media. For my system, the sweet spot is around 20-30% Mg media. Here is a quick video on prepping for the top up : [/url] Sent from Singapore Reef Club mobile app Quote Link to comment Share on other sites More sharing options...
SRC Supporter SubzeroLT Posted May 6, 2020 Author SRC Supporter Share Posted May 6, 2020 12 hours ago, Wai6866 said: Bro, the calcium reactor feed pump and main pump is it on 24hr? Yes, the recirculating pump of the CR should be left on 24/7. There are many ways to set up the calcium reactor. Each has its pros & cons. Personally i leave the feed pump on 24/7 as well. And turn off the CO2 instead. Quote Facebook : https://www.facebook.com/mysliceofnature/ Link to comment Share on other sites More sharing options...
SRC Supporter SubzeroLT Posted May 6, 2020 Author SRC Supporter Share Posted May 6, 2020 Last week's long weekend was great for getting some mini projects started. Managed to make a new lid for the external skimmate & waste water collector. Now it looks like this An external skimmate collector is extremely convenient. There are float switches inside to notify me when the bucket is full & also turn off the skimmer so it won't flood the place. The bucket is used for discharged Alkatronic waste water as well. Generally it is emptied once every few weeks. It used to look like this Long weekend project Top view. The ping pong ball is to allow air to leave the bucket as it is filled with water. And yet have a light seal to prevent smell from coming out. Above it is a compartment for activated carbon The grate at the bottom is a part purchased from Daiso Activated carbon. Dual float switch. The lower one is to notify me that the bucket is 'quite full'. Skimmer is not switched off. I'm only notified by email/warning light to empty the bucket. The skimmer will switch off only when the upper float switch is triggered (i.e. very full). This is the Apex neptune program for the skimmer Top view. All fixed up. 1 Quote Facebook : https://www.facebook.com/mysliceofnature/ Link to comment Share on other sites More sharing options...
Wai6866 Posted May 6, 2020 Share Posted May 6, 2020 Thanks Yes, the recirculating pump of the CR should be left on 24/7. There are many ways to set up the calcium reactor. Each has its pros & cons. Personally i leave the feed pump on 24/7 as well. And turn off the CO2 instead. Sent from Singapore Reef Club mobile app Quote Link to comment Share on other sites More sharing options...
Subbu PD Posted May 6, 2020 Share Posted May 6, 2020 Looks cool and creative... Quote Link to comment Share on other sites More sharing options...
vikneshrajoo Posted May 6, 2020 Share Posted May 6, 2020 Very impressive DIY u got there. Sent from my SM-G955F using Tapatalk Quote Link to comment Share on other sites More sharing options...
SRC Supporter SubzeroLT Posted May 8, 2020 Author SRC Supporter Share Posted May 8, 2020 It was extremely inconvenient to realize the compressor temperature controller is not working properly at 11pm. I noticed the compressor switching on/off more frequently but didn't think much of it. It happened to be a lot worse now. Noticed it suddenly read the tank temperature as 32degC which triggered the compressor to turn on. Then quickly reduced back down to 27degC within 3min. Tried swapping to a new temperature probe but the issue persisted. It was finally resolved after swapping in a new temperature controller. Then monitored it run a full on/off cycle with the compressor at 3am. This is what the Apex temperature chat looked like before & after the temperature controller change. Forward looking my plan for the temperature controller is : Have a full set on standby (not struggling to replace the components at night) Preventive replacement once every 3 years (my set is 4yrs old) 1 Quote Facebook : https://www.facebook.com/mysliceofnature/ Link to comment Share on other sites More sharing options...
SRC Supporter SubzeroLT Posted May 8, 2020 Author SRC Supporter Share Posted May 8, 2020 Some housekeeping pics : I shared about these nice Maxpect tweezers a couple of weeks ago. Couple with long rubber gloves (up to the armpit), it was easy to pick out accumulate debris from the sand bed. Fallen dead frags, bits of glue, vermatid snail shells etc. I'm using the trusted DD magnet glass cleaner for the most of the glass. And this one with a very long handle for the bottom edge & hard to reach areas. This seachem scraper isn't cheap in comparison with other brands but at least it does a good job (and floats) The stress of barb connections on the tubes + occasional knocks have caused my tubes to crack & leak before. As part of preventive maintenance, I also re-did some tube connections to the calcium reactor by snipping off the end of the tube & re-connect. Then did a soap bubble test to ensure there are no leaks. Quote Facebook : https://www.facebook.com/mysliceofnature/ Link to comment Share on other sites More sharing options...
SRC Supporter Harlequinmania Posted May 9, 2020 SRC Supporter Share Posted May 9, 2020 Always very informative reading your thread ,,,Sent from Singapore Reef Club mobile app Quote 1000 Gallon Tank in the Hole http://www.sgreefclub.com/forum/topic/120957-1000-gallon-3d-hole-in-the-wall/ Link to comment Share on other sites More sharing options...
SRC Supporter SubzeroLT Posted May 9, 2020 Author SRC Supporter Share Posted May 9, 2020 9 minutes ago, he said: Always very informative reading your thread ,,, Sent from Singapore Reef Club mobile app Thanks Many tips were learned from you & visiting your fish room Quote Facebook : https://www.facebook.com/mysliceofnature/ Link to comment Share on other sites More sharing options...
SRC Supporter SubzeroLT Posted May 9, 2020 Author SRC Supporter Share Posted May 9, 2020 I may have shared this before but some folks brought this topic up recently. A small hack to ensure the Clarisea roll winds up nicely without bunching up in the middle. Basically the root cause is the fleece is wound v tight, causing the white acrylic to warp a little (i.e. becoming a curved edge). Workaround is to stiffen the white acrylic by making use of the clear acrylic housing. What i've done was to insert a 12mm piece of acrylic in between. You can just use an egg crate as well (they are about 12mm thick too). Just make sure the reinforcement piece does NOT touch the fleece. 1 Quote Facebook : https://www.facebook.com/mysliceofnature/ Link to comment Share on other sites More sharing options...
nornicle1 Posted May 9, 2020 Share Posted May 9, 2020 Eric your informative posts are very educational thank you. How would you recommend someone starting a tank up dial in and increase dosing if using a calcium reactor (I am starting a tank similar in size to you but no existing livestock). I also have access to dosing. Quote Link to comment Share on other sites More sharing options...
SRC Supporter SubzeroLT Posted May 9, 2020 Author SRC Supporter Share Posted May 9, 2020 2 hours ago, nornicle1 said: Eric your informative posts are very educational thank you. How would you recommend someone starting a tank up dial in and increase dosing if using a calcium reactor (I am starting a tank similar in size to you but no existing livestock). I also have access to dosing. I'm Leon (not Eric). In any case, there are many ways to set up a calcium reactor. No one method is correct, so just adapt accordingly. My method is to sync up the flow rate to pH level and not rely on the solenoid to shut off the CO2 when the desired pH is reached. For a start, you can consider an effluent flow rate of about 40ml/min. Measure it. Then tune the CO2 bubble count to reach a target pH level. A good starting point is 6.8pH. Start measuring the KH levels of the tank. Maybe twice a day at the exact same time. If KH drops over a 24hr period, then make the effluent more concentrated by reducing the pH level. Do this until the lower limit of ~ 6.4pH is reached. If lower than this, the calcium reactor will tend to have too much bubbles internally. If the tank demand more kH, proceed to increase the effluent flow rate. You may need to increase the bubble count to maintain the pH level as well. If the tank demands less kH, then consider increasing pH or simply switch off the CO2 for a short period of time. Some folks say the effluent rate is difficult to control. I agree as well. Consider the Ecotech Versa peristaltic pump to feed water for the CR. Its not expensive compared to other peristaltic pumps out there & the value it provides - i.e. very good control over the effluent rate & makes tuning the CR a lot easier. For reference, below is my calcium reactor PH measurement (orange line) vs the KH measurement (blue line). 1 Quote Facebook : https://www.facebook.com/mysliceofnature/ Link to comment Share on other sites More sharing options...
nornicle1 Posted May 9, 2020 Share Posted May 9, 2020 thanks apologies Leon! if you have very few corals at the start is there a ‘ramp’ up of calcium reactor use, ie can I just run it with very little co2 when the use is very little too? Quote Link to comment Share on other sites More sharing options...
SRC Member Mahesh Posted May 9, 2020 SRC Member Share Posted May 9, 2020 Hi Leon, would like to know which ph measuring inst, solenoid do u use and recommend? I understood u r not cutting of ur CO2 when desired pH achieved. Sent from Singapore Reef Club mobile app Quote Link to comment Share on other sites More sharing options...
SRC Supporter SubzeroLT Posted May 9, 2020 Author SRC Supporter Share Posted May 9, 2020 41 minutes ago, nornicle1 said: thanks apologies Leon! if you have very few corals at the start is there a ‘ramp’ up of calcium reactor use, ie can I just run it with very little co2 when the use is very little too? Yes, the idea of starting with high PH of around 6.8 is to make the effluent "less concentrated". To reach this, you will probably need very little CO2. Maybe 1 bubble every 1-2 seconds. And as more corals are added & higher demand, lower the pH to make the effluent 'more concentrated". Quote Facebook : https://www.facebook.com/mysliceofnature/ Link to comment Share on other sites More sharing options...
SRC Supporter SubzeroLT Posted May 9, 2020 Author SRC Supporter Share Posted May 9, 2020 30 minutes ago, Mahesh said: Hi Leon, would like to know which ph measuring inst, solenoid do u use and recommend? I understood u r not cutting of ur CO2 when desired pH achieved. Sent from Singapore Reef Club mobile app Not relying on the solenoid to cut out the CO2 is just a matter of fine tuning the effluent flow rate & bubble count. Not so much related to the equipment used. In any case, i'm using the Apex Neptune to measure pH. Using a Milwaukee double junction pH probe. For CO2 solenoid, i'm using an Ocean Free dual gauge solenoid. 1 Quote Facebook : https://www.facebook.com/mysliceofnature/ Link to comment Share on other sites More sharing options...
SRC Supporter SubzeroLT Posted May 10, 2020 Author SRC Supporter Share Posted May 10, 2020 Tank maintenance + water change weekend. Usual maintenance routine includes : Measure water parameters. For me, I usually measure it just before water change to know what its like at its 'worst' water condition Look for aiptasia & inject with Aiptasia X Trim corals Measured Phosphate levels. Close to 0.1ppm phosphate after the conversion. Time to change the rowaphos. Nitrates : 5ppm. Hmm...gone up a little due to increased feeding. Need to ramp up flow of the sulfur reactor a little. Calcium : 420ppm, Mg : 1440ppm Alkalinity : 2 Quote Facebook : https://www.facebook.com/mysliceofnature/ Link to comment Share on other sites More sharing options...
SRC Member soggycookies Posted May 10, 2020 SRC Member Share Posted May 10, 2020 Tank maintenance + water change weekend. Usual maintenance routine includes : Measure water parameters. For me, I usually measure it just before water change to know what its like at its 'worst' water condition Look for aiptasia & inject with Aiptasia X Trim corals Measured Phosphate levels. Close to 0.1ppm phosphate after the conversion. Time to change the rowaphos. Nitrates : 5ppm. Hmm...gone up a little due to increased feeding. Need to ramp up flow of the sulfur reactor a little. Calcium : 420ppm, Mg : 1440ppm Alkalinity : Thanks for sharing your meticulous maintenance schedule with us Leon. Always a great reference point for others in the hobby. Cheers!Sent from Singapore Reef Club mobile app Quote Link to comment Share on other sites More sharing options...
weizhi10 Posted May 10, 2020 Share Posted May 10, 2020 How to get a new set of controller? It was extremely inconvenient to realize the compressor temperature controller is not working properly at 11pm. I noticed the compressor switching on/off more frequently but didn't think much of it. It happened to be a lot worse now. Noticed it suddenly read the tank temperature as 32degC which triggered the compressor to turn on. Then quickly reduced back down to 27degC within 3min. Tried swapping to a new temperature probe but the issue persisted. It was finally resolved after swapping in a new temperature controller. Then monitored it run a full on/off cycle with the compressor at 3am. This is what the Apex temperature chat looked like before & after the temperature controller change. Forward looking my plan for the temperature controller is : Have a full set on standby (not struggling to replace the components at night) Preventive replacement once every 3 years (my set is 4yrs old) Sent from Singapore Reef Club mobile app Quote Link to comment Share on other sites More sharing options...
SRC Supporter SubzeroLT Posted May 10, 2020 Author SRC Supporter Share Posted May 10, 2020 48 minutes ago, weizhi10 said: How to get a new set of controller? You can get it from the components from ebay or from Sim Lim Tower for self replacement. But do this only if one is savvy with electrical things. Else just get it from the person who set up your compressor. Quote Facebook : https://www.facebook.com/mysliceofnature/ Link to comment Share on other sites More sharing options...
SRC Supporter SubzeroLT Posted May 11, 2020 Author SRC Supporter Share Posted May 11, 2020 Measured my phosphate yesterday. Reading was about 0.1ppm. Sharing some pics of the process. Last Rowaphos change was 7th March. Its now 10th May. So its roughly 2 months replacement cadence. Some pics of the replacement process : This is how the Rowaphos media is stored - with a small tub of damp sponge to ensure it remains humid inside the container & not letting the media dry out. About 11cm height of media is right for my tank (850 liters) to last about 2 months. Sponge & separators removed for the moment. Using the container to rinse the rowa with RODI. After about 6 rounds of rinsing, the reddish fines are washed away and water looks like this. Take the rowa out. Put in the sponge & separators Put old test tube over the center tube. Then scoop in the washed rowa Once all hooked up, the flow rate is tuned for the Rowa level to tumble & rise to about 75% height of the reactor . Never reaching the sponge else some media will escape into the tank or clog up the sponge. Record in diary & set reminder to check phosphate levels 6-8 weeks later. Quote Facebook : https://www.facebook.com/mysliceofnature/ Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.