joeyttk Posted December 13, 2005 Share Posted December 13, 2005 Hi, I put my chiller below the tank and I have to constantly leave the cupboard door open to ensure good circulation. Does anyone knows where can I get power hinges that I can customized to run off a thermostat ? I did a few searches on the net and only found those mega door swingers for gates or fences. I did saw someone mod a celica [i.e. car] in US where there is a power hinges that push open a compactment to reveal their nos. any ideas where can I get cupboard-door-size powered hinges ? Quote Link to comment Share on other sites More sharing options...
Kotobuki Posted December 13, 2005 Share Posted December 13, 2005 Bro, I think a better option will be drill 2 holes behind your cabinet. Mount 2x 6" CPU Fan. 1 in 1 out for circulation. You may wanna include a themalstat to trigger it if yopu want. My 2cents Tak Quote Link to comment Share on other sites More sharing options...
SRC Member ervine Posted December 13, 2005 SRC Member Share Posted December 13, 2005 too complex solution for a simple problem... try the fan method.... Quote Link to comment Share on other sites More sharing options...
joeyttk Posted December 16, 2005 Author Share Posted December 16, 2005 I do have a 12inch hole for ventilation on one side. However, without leaving the cupboard door open, even with the hole and big fan [A/C] black colour type from sim lim tower, the cupboard temp hovers around 45 degree c. cannot drill more holes because my tank is mounted on a floor2ceiling cupboard and serve as a partition wall. the other side has black shiny laminate, i.e. will be a bad idea to drill holes. so the only thing now is that I left the door to the cupboard open. One last thing, I had the 12 inch black cpu fan but they burnt out after 5-6 months [i guess temp too high]. I DIY it with a simple 35 degree c thermostat so that fan auto on when chiller is on. anyone can reco a good fan to use ? mine coz around 20 dollars from sim lim tower. Quote Link to comment Share on other sites More sharing options...
SRC Member ervine Posted December 16, 2005 SRC Member Share Posted December 16, 2005 get a AC fan instead? usually it's not the DC fan that blows but the transformer... Quote Link to comment Share on other sites More sharing options...
Kotobuki Posted December 20, 2005 Share Posted December 20, 2005 Yup an AC fan will do. And also stuck a piece of wool on the cuboard door... leave a 1 inch gap will do. Just remember, HOT air rises.... design the rest yourself ba. Quote Link to comment Share on other sites More sharing options...
SRC Member nivlac Posted December 20, 2005 SRC Member Share Posted December 20, 2005 depends on the size of cabinet what type of chiller you run as well. I have a small 2.5 ft x 2.5 ft x 4 ft high cabinet. Even with 2 x fans and 5 holes at the side, chiller has to work non stop. Quote Link to comment Share on other sites More sharing options...
joeyttk Posted December 21, 2005 Author Share Posted December 21, 2005 hi, I am already using AC fans leh... the big fan only comes in AC. only when the cupboard doors are open completely will my chiller cool ,my 5.5ft tank down to 27 degree in 2 hours. So back to the original question, does anyone knows where to buy those power hinges so I can customized my door ? thanks for all the advise on how to cool down the chiller, trust me when I said I already tried a lot of ways, cutting more holes not an options, fan cooling thru my single 12" hole on one side with an AC fan also not doing well. Fan motor cannot stand the constant heat, and usual breaks down after 6 months. Quote Link to comment Share on other sites More sharing options...
Kotobuki Posted December 22, 2005 Share Posted December 22, 2005 Bro, you may wanna post a pic of your current setup so dat we can all brain storm for ya. Where is your chiller located? Quote Link to comment Share on other sites More sharing options...
jasMarine Posted December 22, 2005 Share Posted December 22, 2005 Bro, How about adding ventilation line holes on your cabinet doors. The doors look like with lines from front view cause hole facing downwards. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.