Jump to content

Another DIY LED lighting


Jameshong
 Share

Recommended Posts

Hahaha...although lite set completed but now don't know how to hang the lite leh!

Wife not allow to drill hole on the wall or ceiling so must think of a way to hold the lite. My initial thought is to DIY a square bar or round aluminum rod to create reverse L shape to hold the lite or try to source off the shelf type. Isit good?

Anyone have any idea or input? please chip in........

post-1182-049500100201281969137_thumb.gi

Knowing is not enough; we must apply. Willing is not enough; we must do. - Goethe

Link to comment
Share on other sites

  • SRC Member
Hahaha...although lite set completed but now don't know how to hang the lite leh!

Wife not allow to drill hole on the wall or ceiling so must think of a way to hold the lite. My initial thought is to DIY a square bar or round aluminum rod to create reverse L shape to hold the lite or try to source off the shelf type. Isit good?

Anyone have any idea or input? please chip in........

Bro, I got spare aluminum frame...try try see if can fit

-
5x1.5x2ft Tank


5x2.5x2 Full Height Tank

Link to comment
Share on other sites

Bro, I got spare aluminum frame...try try see if can fit

Hi bro,

Any picture? If suitable, I will go and buy it.

post-1182-049500100201281969137_thumb.gi

Knowing is not enough; we must apply. Willing is not enough; we must do. - Goethe

Link to comment
Share on other sites

Here is the picture...I got spare lah..don't buy

How you join it to form L shape?

post-1182-049500100201281969137_thumb.gi

Knowing is not enough; we must apply. Willing is not enough; we must do. - Goethe

Link to comment
Share on other sites

Here is the picture...I got spare lah..don't buy

How you join it to form L shape?

post-1182-049500100201281969137_thumb.gi

Knowing is not enough; we must apply. Willing is not enough; we must do. - Goethe

Link to comment
Share on other sites

I think they have a right angle fitting for joining.

6.5 * 2 * 2 + 3.75 * 1.5 *1.5,(Decomn on 14/9/08)
4*2*2 + 2.5*1.25*1.25 (Decomn on 1/8/09)
5*2*2 (Fully LED light system, 140 3 watt SSC leds with 60 degree lens)(Decomm)
2.5*2*2(Fully LED Light System,96 3 watt SSC leds with 60 degree lens)(Decomm)

5*2.5*2(LED only)

Eheim return 1 * pump

1 HP Daikin compressor with cooling coil
2 Jebao OW40, 1 ecotech MP40,
1X6085 Tunze wm,

1 CURVE 7 Skimmer

  1 DIY 80 led control by Bluefish mini 

1 radion XR30W G2, 2 Radion XR15G3

Sump area lite by 5 ft T5 , 6 * SSC 3 watt red LED for refugium

1 Full spectrum E27 led light

1 CR control by bubble count

Start No Water Change since 1st Dec 2016

Add new 2.5x2x 1.5 ft 

 nLekOfpYts.jpg
[/quote]


 

Link to comment
Share on other sites

Same shop that sells the aluminum frame sell these accessories too....

ok. Let have a good talk when you back from Australia..... :groupwavereversed: !

post-1182-049500100201281969137_thumb.gi

Knowing is not enough; we must apply. Willing is not enough; we must do. - Goethe

Link to comment
Share on other sites

Here is my thought of MY 2 Lite stand holder design, 1st is double bar and 2nd is single bar (Dimension not confirm yet).

I personnelly prefer single bar if it can withstand 1.5kg holding weight..

Please comment.

post-1282-0-85244900-1336531032.jpg

post-1282-0-77114200-1336531515.jpg

post-1182-049500100201281969137_thumb.gi

Knowing is not enough; we must apply. Willing is not enough; we must do. - Goethe

Link to comment
Share on other sites

  • SRC Member

Single will be nice but you have to balance it ...

Selling big game fishing equipment. Stella 20k / 17k .. made in Japan jigging blue rose / kabuzu popping rod... pm for prices

Link to comment
Share on other sites

  • SRC Member

Here is my thought of MY 2 Lite stand holder design, 1st is double bar and 2nd is single bar (Dimension not confirm yet).

I personnelly prefer single bar if it can withstand 1.5kg holding weight..

Please comment.

A stronger elbow joint should be able to hold the 1.5kg. There are many different types of elbow joint available for your choice.

-
5x1.5x2ft Tank


5x2.5x2 Full Height Tank

Link to comment
Share on other sites

A stronger elbow joint should be able to hold the 1.5kg. There are many different types of elbow joint available for your choice.

Wow...you so free still can surfing net in Australia har...lol!

post-1182-049500100201281969137_thumb.gi

Knowing is not enough; we must apply. Willing is not enough; we must do. - Goethe

Link to comment
Share on other sites

  • SRC Member

I think the bar holder may need two. The other one nearer the bottom end. I had almost same setup install rear of cabinet using the mazarra light mounts. For added safety.With only one there might have some free play movement.

Link to comment
Share on other sites

I think the bar holder may need two. The other one nearer the bottom end. I had almost same setup install rear of cabinet using the mazarra light mounts. For added safety.With only one there might have some free play movement.

Yes...you are right.

For safety, I will add 2 more bar holder if select option 1 else add 1 more for option 2... :thumbsup: .

Btw, possible to post the picture of your mazarra stand here?

post-1182-049500100201281969137_thumb.gi

Knowing is not enough; we must apply. Willing is not enough; we must do. - Goethe

Link to comment
Share on other sites

where can get it?

James, go to Clementi hardware shop that you got your PVC cutter.. get a endmill cutter/countersink drill bit+allen key bolt & Thread Taper. You can achieve the same "L" Shape... Pls find pic below....

post-9248-0-98555900-1337008208_thumb.jp

Cheers..

30ikthj.gif30ikthj.gif30ikthj.gif
BANNER.jpg
1-3.jpg


LFS Map in singapore
__________________
><((((º>`·.¸¸.·´¯`·.¸.·´¯`·...¸><((((º>
·´¯`·.¸. , . .·´¯`·.. >((((º>
Cheers and Happy Reefing....

Link to comment
Share on other sites

James, go to Clementi hardware shop that you got your PVC cutter.. get a endmill cutter/countersink drill bit+allen key bolt & Thread Taper. You can achieve the same "L" Shape... Pls find pic below....

Cheers..

Bro Oh, any idea whether Sun Hee hardware @Clementi Ave. 2 selling those aluminium track? :ThanxSmiley:

Link to comment
Share on other sites

Bro Oh, any idea whether Sun Hee hardware @Clementi Ave. 2 selling those aluminium track? :ThanxSmiley:

I dun think so. I'm frequent visitor there...LOL!

post-1182-049500100201281969137_thumb.gi

Knowing is not enough; we must apply. Willing is not enough; we must do. - Goethe

Link to comment
Share on other sites

James, go to Clementi hardware shop that you got your PVC cutter.. get a endmill cutter/countersink drill bit+allen key bolt & Thread Taper. You can achieve the same "L" Shape... Pls find pic below....

post-9248-0-98555900-1337008208_thumb.jp

Cheers..

Thanks bro. I have a few sizes of thread taper, few sizes of allen key bolts & nuts on hand liao..so what I need is the countersink drill bit only. Will go down this weekend to see see look look.... :thumbsup:!

post-1182-049500100201281969137_thumb.gi

Knowing is not enough; we must apply. Willing is not enough; we must do. - Goethe

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share




  • Join us on the largest Reefing community in Asia!

    Sign up and share your reefing journey with us, make friends and get helps from the community .

     

  • Topics

  • Latest Update

    1. 0

      Hang on Mini ATS algae scrubber

    2. 0

      SPELL CASTER +27790293623]] ╬ TRADITIONAL HEALER/ SPIRITUAL HEALER IN Pretoria, Diepsloot, Durban, Sasolburg, Botshabelo,  Bothaville, Potchefstroom, Klerksdorp, Secunda, Middleburg, Ermelo, Witbank, Mafikeng, Lichtenburg, Rustenburg,  Nelsprui

    3. 0

      SPELL CASTER +27790293623]] ╬ TRADITIONAL HEALER/ SPIRITUAL HEALER IN Groblersdal, Secunda, Middleburg, Newcastle, Polokwane, Port Elizabeth, East London, Ermelo, Kimberly, Mthatha, Queenstown,

    4. 0

      +27790293623 Bring back lost lover IN Nelspruit , Newcastle ,Nquthu , Nylstroom , paarl , paulpietersburg , Pietermaritzburg , Pietersburg , Pinetown , Plettenbergbay , Polokwane , Port Alfred , Port Elizabeth , Postmasburg , Pretoria , Queenstown , Sout

    5. 0

      +27790293623 in Bring back lost lover / love spell caster IN Kimberley , Kirkwood , Klerksdorp , Knysna , Kokstad , Komga ,Kroonstad ,Kuruman , Lady frère , +27790293623 Bring back lost lover IN Nelspruit , Newcastle ,Nquthu ,

×
×
  • Create New...